Fisher-Price N9326 Instruction Sheet

N9326www.fisher-price.com

10 11Transmitter Wall Mount InstallationTo prevent strangulation with power cord, never place transmitter within reach of child.WARNINGIMPORTANT! Test

10 11• To provide the greatest viewing range, we recommend you install the wall mount bracket at least six feet from the floor. • Make sure the camera

12 13Transmitter Wall Mount Installation• Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall.• Hold the wall moun

12 13• Fit a wall anchor into each of the drilled holes.• Tap each wall anchor lightly with a hammer until the ends of each wall anchor are even with

14 15• Position the cord wrap against the wall, so that it is centered below the wall mount bracket and as close to the floor as possible.• Move the co

14 15• Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall.• Place a wall anchor into each of the drilled holes.•

16 17Transmitter Wall Mount Installation• Align the holes on the cord wrap with the wall anchors. • Insert two screws into the holes in the cord wrap

16 1710Transmitter Wall Mount InstallationIMPORTANT! Make sure the cord is taught between the transmitter and cord wrap. Excess cord can form loops or

18Setup/On Screen Displays Main Menu• First, turn both transmitter and receiver power ON. Then press the main power/menu select button on the receiver

19Setup/On Screen Displays Sounds Turn sounds off Select nature sounds Select heartbeat sounds Return to previous menu Exit menuIf you turn soun

2Important!To prevent electric shock, do not immerse in water; wipe clean with damp cloth.DANGERTo prevent strangulation with power cord, never place

20Setup/On Screen Displays Night Light Turn night light off Turn night light on Return to previous menu Exit menuIf you turn the night light on t

21 Contrast/Brightness Press left or right side arrows to adjust contrast on the screen. Return to previous menu Exit menuSetup/On Screen Displays

22Setup/On Screen Displays Out of Range The out of range warning will flash on the screen and you will hear a tone when the receiver is out of range o

23• Place the transmitter in the same room with child. Fit the transmitter into the tabletop base. Position the camera lens so it is facing child. For

24 25• To use AC current, unwrap and fully extend the AC adaptor cord (for best reception). Insert the AC adaptor pin into the DC input jack on the r

24 25When the light in baby’s room is too low, the transmitter will automatically switch to night vision mode. The image on the receiver screen will a

26Battery ReplacementIf you need to replace your NiMH rechargeable battery pack, please contact Fisher-Price® Consumer Relations at www.service.fisher

27 28Problem SolutionNo image on receiver screen Press the video screen on/off button. You can also change the voice activated setting to . The vide

27 28Problem SolutionReceiver beeps and displays low battery icon on screenBattery pack in receiver is weak or dead. Use AC adaptor as power source

29FCC Statement (United States Only)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

3• For proper setup and use, please read these instructions.• Please keep this instruction sheet for future reference, as it contains important inform

30RSS-210 ICES-003 CNR-210 NMB-003RSS-210This device complies with RSS-210 of Industry Canada. Operation is subject to the following two cond

31Care• Excess dirt in transmitter microphone will hamper transmission of sound. Wipe all parts with a damp cloth. Do not immerse any part of this mon

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.©2008 Mattel, Inc. All Rights Reserved.® and ™ designate U.S. tra

49101211414FeaturesReceiver Transmitter6147313258AC Adaptor/ChargerTransmitter Tabletop Stand

51 Main Power/Menu Button – Press to turn receiver main power ON; press again for the main menu; press and hold for approximately five seconds to turn

6Fasteners Shown Actual SizeWall Mount PartsWall Mount Bracket Cord Wrap Base StandWall Anchor – 4#8 x 2" Screw – 4

7Charging the Battery (Inside the Receiver)DC Input JackIMPORTANT! Fully charge the receiver (with battery pack inside) for four hours before first-tim

8Testing Sound/Video Reception • Place the transmitter in the room where you intend to use it. • Point the transmitter toward the area you will be mo

9Testing Sound/Video Reception • Place the receiver in the room where you intend to use it.• Press the main power/menu select button on the front of